Industrial Coffee Table

Hey Guys, One of my friends has been updating their living room with new furniture and asked if I would put together some pieces for her. I started with their coffee table. It needed to suit their style which is a more Rustic Industrial look. It also needed to be very durable since she had just gotten a puppy who is going to get big pretty quickly. We went through many options and when I showed her this design, she absolutely loved it. This Industrial Coffee table has legs that are painted to look like Metal, but the whole thing is made out of wood!  This table is a very simple and easy design so it’s a great option for a beginner DIY. On top of that the price point is fantastic.

Make sure you read through the instructions and look over the plans fully before you start your project. Check out the “Before You Start” page for more on tool information, tips & tricks. Always stay safe and wear all safety protection. It is always best to make your cuts as you go and as they say, measure twice and cut once.

If you have any questions just ask away!

 

CLICK HERE – FREE PDF PRINTABLE PLANS!

Shopping List

5 – 2″ x 6″ x 8′

4 – 2″ x 2″ x 8′

2 1/2″ Pocket Screws

2″  Wood Screws

Stain

Primer

Spray Paint

Stainable Wood Filler

Cut List

4 – 2″ x 2″ @ 45″ – LONG SIDE

4 -2″ x 2″ @ 24 1/2″ – SHORT SIDE

10 – 2″ x 6″ @ 48″ – TOP & BOTTOM SHELF

4 – 2″ x 2″ @ 16.5″ – LEGS

Tools Needed

 

Circular Saw

 

Drill

 

Kreg Jig

 

Clamps

 

Measuring Tape

 

Paint Brush

 

 

Pencil

 

Shop Towels

 

Safety Glasses

 

Ear Protection

 

Dust Mask

 

Gloves

The Step-by-Step

The Top & Bottom Shelf Assembly

Build each by Drilling 1 1/2″ Pocket Holes along the long end of the boards.

Use 2 1/2″ Pocket screws & Wood glue to attach the boards together. 

For the bottom shelf, cut out a 1 1/2″ x 1 1/2″ Square out of each corner. This will be where it its into the Frame.

 

The Frame

To assemble the frame you first need to drill 1 1/2″ Pocket hole in each end of the 2″ x 2″ @ 44″ – LONG SIDE & 2″ x 2″ @24 1/2″ SHORT SIDE boards.

Attach the Short Side pieces  to the leg Pieces using 2 1/2″ Pocket Screws & Wood Glue. 

Now attach the 2 Long Side bottom pieces using 2 1/2″ Pocket Screws & Wood Glue

Place the bottom shelf into place, but do not fasten. We will fasten the bottom shelf later on. 

Now that the bottom shelf is in place, we can attach the 2 Top Long Side Pieces using 2 1/2″ Pocket Screws & Wood Glue.

 

Now, Before we can attach the bottom Shelf, and the top into place, we need to finish the frame. 

First, wood fill and sand any holes that are visible, then give the frame a good sand. 

Once the Frame is ready, its time to prime & paint in the colour you have chosen. I used the Rustoleum Metallic Dark Steel. It took one coat of the primer and 2 coats of paint.

Once the paint is dry you can attach the bottom shelf  &  the Top to the frame using 2 1/2″ Wood screws. Attach through the Frame.

Tip: attach the bottom shelf first by flipping the table on its side. Attach the top at the end so that it does not get damaged being against the floor.

 

The Final Finish

Just as you did for the frame, use wood filler on the table top and bottom shelf.

Once it has dried, give it a really good sand. 

Mask off the Painted frame and stain the top and bottom shelf. 

Once the stain has dried apply 2 coats of Polyurethane.

 

 

Now subscribe below to get instant emails to new posts & projects.

&

Check me out on Facebook & Pinterest too!




Rustic Chunky Leg Coffee Table

Hey Guys, for all of you who have loved the look of the Rustic X Coffee table, but did not have the room for the length of it, here is a great alternative, the Rustic Chunky Leg Coffee Table. I have taken the table and turned it a 3 Foot square table. Now, with it being square, the 2” x 4” legs would not look right. Instead, 4” x 4” boards were used as the legs to keep the table looking balanced.

 

Make sure you read through the instructions and look over the plans fully before you start your project. Check out the “Before You Start” page for more on tool information, tips & tricks. Always stay safe and wear all safety protection. It is always best to make your cuts as you go and as they say, measure twice and cut once.

If you have any questions just ask away!

CLICK HERE – FREE PRINTABLE PDF PLANS 

Shopping List

4 – 2” x 4” x 8’
 
2 – 2” x 2” x 8’
 
1 – 1” x 10” x 8’
 

3 – 2” x 8” x 8’

L Brackets

Screws

2 ½” pocket Screws

1 ¼” Pocket Screws

2 “ Wood Screws

Paint

Stain

Polyurethane

Stainable Wood Filler

Cut List

8- 2” x 4” @ 27 ¾” – SUPPORTS
 
4 – 4” x 4” @ 16 ½” – LEGS
 
5 – 2” x 8” @ 36 ¼” – TOP
 
3 – 1 “ x 10”  @ 27 ¾” SHELF
 
2 – 2” x 2” @ 26 11/16″ From LONG END to SHORT END – 65 Degree cuts are Parallel **SEE TIP to Cut**
 
4 – 2” x 2” @ 11 3/8″ From SHORT END of 65 Degree angle to Long End of 40 Degree Angle **SEE TIP to cut**

Tools Needed

 
 
Mitre Saw

 

Kreg Jig

 

Drill

 

Sander

 

Clamps

 

Pencil

 

Tape Measure

 

Wood Glue

 

Shop Towels

 

Paint Brush

 

Ear Protection

 

Safety Glasses

 

Dust Mask

The Step-by-Step

The Base

First, pocket holes are needed on both ends of each 2 “ x 4” @ 27 ¾” Support Board

Use 2 ½” Pocket Screws & Wood Glue to attach these boards to the Legs. The top supports will be flush with the top of the Legs, the bottom support will be 2 ¼” from the bottom of the leg.

 

Next, we need to assemble the bottom shelf.

Drill ¾” Pocket holes on all sides of the boards. These will be used to attach the shelf together as well as to attach the shelf to the supports.

Use 1 ¼” Pocket screws & Wood Glue to assemble the boards together & attach to the supports.

 

Now its time to attach the X’s. Use 2 “ Wood screws and wood Glue to attach through the supports and use 2 ½” Pocket screws to attach the smaller pieces to the long Piece. Start with the Long piece, and then add the 2 smaller pieces.

TIP: To Cut these pieces, its best to first lay out the Full piece and mark off your lines. Cut & Install that piece first. For the smaller pieces, do the same thing. Mark and cut one full piece then place in behind the other and mark off the other cuts your are going to need. These will be around 40 Degrees

 

The Top

 Drill 1 ½” pocket holes in the 5 boards for the top, then use 2 ½” Pocket screws & Wood Glue to attach the boards together.

Assemble & Finish

Spray paint the 4 corner brackets and the co-ordinating Screws

While the brackets are drying, it’s time to finish the table. Use the stainable wood filler to fill in any pocket holes, the gaps in the top and any other imperfections.

 Once the wood filler has dried, give everything a good sand.

 Next, paint, stain and polyurethane depending on how you decided the table will look.

Note: remember if you will be painting the base of the table, do not forget to prime first.

 

Use 2 “ Wood Screws through the top support to attach the top.

 Finally attach the 4 corner brackets to the table top edge with the screws you also painted.

 

 

Now subscribe below to get instant emails to new posts & projects.

&

Check me out on Facebook & Pinterest too!




Side Table with a Magazine Rack & Shelf

Hey all, here is the other gift that was made for father’s day. A couch side table for my husband that has a magazine rack and shelf. The best part is how compact it is for the limited space and its custom height to fit right over the arm of the couch. It doesn’t take much to build this and can be made for under $25.00.

 

Make sure you read through the instructions and look over the plans fully before you start your project. Check out the “Before You Start” page for more on tool information, tips & tricks. Always stay safe and wear all safety protection. It is always best to make your cuts as you go and as they say, measure twice and cut once.

If you have any questions just ask away!

CLICK HERE – FREE PRINTABLE PDF PLANS 

Shopping List

1 – 1” x 6” x 8’

1 – 1” x 10” x 4’

Wood Glue

1 – 1” x 8” x 4’

1 ¼” Wood Screws

Stain-able Wood-Filler

Stain

Polyurethane

Cut List

1 – 1” x 12” @ 16” Top

1 – 1” x 8” @ 16” Bottom

2 – 1” x 6” @ 23” Sides

3 – 1” x 6” @14 ½” Shelf & Mag Front

1 – 1” x 8” @ 16” Back Of Magazine

Tools Needed

 

Circular Saw

 

Sander

 

Drill

 

Measuring Tape

 

Pencil

 

Shop Towels

 

Gloves

 

Safety Glasses

 

Ear Protection

Step-By-Step

 

First thing you will do is pre-sand the boards, otherwise you will have a hard time once the stand is built.

 

Take the 2 boards for the sides and attach both the top and bottom boards using 1 ¼” wood screws and wood glue

Build the little shelf using 2 of the 1” x 6” @ 14 ½” boards. First attach the back board then attach the bottom of the shelf. Again use 1 ¼” wood screws to attach

The last 2 boards are for the magazine rack. The large 1” x 8” board will be the back piece (going against the couch) The smaller is for the front. Use the 1 ¼” wood screws to attach

All that is left is to finish. Fill with stain-able wood filler, Give another sand, stain and apply your polyurethane.

 

Now subscribe below to get instant emails to new posts & projects.

&

Check me out on Facebook & Pinterest too!